Page 1
RELEASED Ver-C Toro 2016
Form No. 3393-925 Rev C TimeCutter SW Riding Mower Model No. SW TimeCutter Models
Setup Instructions
Setup Loose Parts Use the chart below to verify that all parts have been shipped.
Procedure Description Qty. Use
1 No parts required Connect the battery.
Rear hitch 1 Bolt (5/16 x 1 inch) 22 Locknut (5/16 inch) 2
Install the rear hitch.
Steering wheel 1 Top cover 1 Locknut 1 Rear cover 1
3 Screws 2
Install the steering wheel.
Seat assembly 1 Seat rod 1 Hairpin cotter pins 24 Spacers (certain models only) 2
Install the seat assembly.
5 Grass deflector (if not installed) 1 Install the grass deflector.
6 No parts required Check the mower adjustment.
Ignition key 1 Hose coupling (not included with CE models) 1
Operator's Manual 1 Engine Owners Manual (non-Toro engines) 1
7 KeyChoice key (blue) 1
Complete the setup.
Note: Determine the left and right sides of the machine from the normal operating position.
2016The Toro Company 8111 Lyndale Avenue South Bloomington, MN 55420
Register at www.Toro.com. Original Instructions (EN) Printed in the USA All Rights Reserved *3393-925* C
Page 2
RELEASED Ver-C Toro 2016
1 Connecting the Battery
No Parts Required
Procedure
WARNING CALIFORNIA
Proposition 65 Warning Battery posts, terminals, and related
accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm.
Wash hands after handling.
1. Locate the battery and negative battery cable.
2. Remove the plastic cap from the negative battery post.
3. Remove the fasteners on the negative battery cable, and use them to secure the negative battery cable to the negative battery post (Figure 1).
G018395
2
1
4
3
6
5
g018395
Figure 1
1. Negative battery cable 4. Negative battery post cap 2. Wing nut 5. Carriage bolt 3. Washer 6. Negative battery post
2 Installing the Rear Hitch
Parts needed for this procedure:
1 Rear hitch
2 Bolt (5/16 x 1 inch)
2 Locknut (5/16 inch)
Procedure 1. Install the bracket to the frame as shown in Figure 2.
2. Torque the bolts between 19.8 and 25.4 N-m (175 and 225 in-lb).
g028437
Figure 2
1. Bolts 2. Locknuts
2
Page 3
RELEASED Ver-C Toro 2016
3 Installing the Steering Wheel
Parts needed for this procedure:
1 Steering wheel
1 Top cover
1 Locknut
1 Rear cover
2 Screws
Procedure 1. Rotate the steering column up to the user position
(Figure 3).
g027703
Figure 3
2. Position the steering wheel as shown in Figure 5.
3. Install the steering wheel and top cover to the steering column with the locknut (Figure 4).
4. Torque the locknut between 36.6 and 44.7 N-m (27 and 33 ft-lb).
5. Install the steering-wheel cover.
g027737
Figure 4
1. Steering-wheel cover 4. Top cover 2. Locknut 5. Column 3. Steering wheel
6. Install the rear cover to the back of the footrest with the tabs at the bottom inside the footrest and the 2 screws in the top (Figure 5).
Note: Ensure the tabs of the rear cover are inside the footrest.
g027887
Figure 5
1. Back cover 2. Screws
3
Page 4
RELEASED Ver-C Toro 2016
4 Installing the Seat Assembly
Parts needed for this procedure:
1 Seat assembly
1 Seat rod
2 Hairpin cotter pins
2 Spacers (certain models only)
Procedure 1. Install the seat assembly to the frame with the seat rod,
2 hairpin cotter pins, and 2 spacers (certain models only) as shown in Figure 6.
g027723
Figure 6
1. Seat assembly 3. Hairpin cotter 2. Spacers 4. Seat rod with hairpin cotter
installed
2. Connect the seat switch (Figure 7).
g027695 g027695
Figure 7
3. Route the wire harness to the right side of the machine and push the plastic connector into the seat frame hole (Figure 8).
g028383
1 2
g028383
Figure 8
1. Plastic connector in seat frame hole
2. Wire harness
4
Page 5
RELEASED Ver-C Toro 2016
5 Installing the Grass Deflector
Parts needed for this procedure:
1 Grass deflector (if not installed)
Procedure If the grass deflector is not installed, remove it from the packaging and install it onto the mower deck. Refer to your Operators Manual for the correct procedure to install the grass deflector.
6 Checking the Mower Adjustment
No Parts Required
Procedure Adjust the side-to-side level and the front-to-rear blade slope. Use the relevant procedures in the Operator's Manual to verify that the deck is level, and make any adjustments as necessary. Refer to the Operator's Manual for more information.
7 Completing the Setup
Parts needed for this procedure:
1 Ignition key
1 Hose coupling (not included with CE models)
1 Operator's Manual
1 Engine Owners Manual (non-Toro engines)
1 KeyChoice key (blue)
Procedure Checking the Tire Pressure
Check the front and rear tires for proper inflation; refer to Checking the Tire Pressure in the Operator's Manual for the recommended inflation pressure.
Checking the Side-Discharge Chute
Remove the packing restraint holding the side discharge chute up and lower the chute into place.
Checking the Engine-Oil Level
Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking the Oil Level in the Operator's Manual.
Keep all the following items with the machine:
Ignition key
KeyChoice key (blue)
Hose coupling (not included in CE models)
Operator's Manual
Engine Owners Manual (non-Toro engines)
5
Page 6
RELEASED Ver-C Toro 2016
Notes:
